正確使用
自動攪拌一體機有利于施工的順利進行,并且可以提高工程工作效率,如果沒有正確使用會損害設備的機械部件,減少它的使用壽命。使用時的重中之中是要嚴格按照使用說明進行操作,一般在夏季如果自動攪拌一體機溫度過高應該立刻停下來,等溫度降下來后再繼續使用。
The correct use of the automatic mixing machine is conducive to the smooth construction, and can improve the work efficiency of the project. If not properly used, it will damage the mechanical parts of the equipment and reduce its service life. The most important thing in use is to operate in strict accordance with the instructions. Generally in summer, if the temperature of the automatic mixing machine is too high, it should stop immediately and continue to use after the temperature drops down.
1、操作自動攪拌一體機注意液壓系統壓力應符合使用說明書中的規定,不得隨意調整。液壓油的油質和油量應符合原定要求。
1. When operating the automatic mixing machine, pay attention that the pressure of the hydraulic system should comply with the provisions in the operation manual, and should not be adjusted at will. The quality and quantity of hydraulic oil should meet the original requirements.
2、操作自動攪拌一體機注意裝料前,應先排凈拌筒內殘存的積水和雜物。在運輸過程中要不停的轉動,以防混凝土離析?;炷翑嚢柽\輸車到達工地和卸料之前,應先使拌筒全速以14—18轉/分轉動1—2分鐘,然后再進行反轉卸料。反轉之前,應使攪拌筒停穩,然后再開啟反轉。
2. Before operating the automatic mixing machine, pay attention to drain the residual water and sundries in the mixing drum before loading. In the process of transportation, keep rotating to prevent concrete segregation. Before the concrete mixer truck arrives at the construction site and unloads, the mixing drum shall be rotated at full speed at 14-18 rpm for 1-2 minutes, and then reverse unloading shall be carried out. Before reversing, the mixing drum should be stopped stably, and then turn on the reversal.
3、環境溫度高于+25攝氏度,從裝料、運輸、到卸料延續時間不得超過60分鐘,環境溫度低于+25攝氏度,上述時間不得超過90分鐘。
3. If the ambient temperature is higher than + 25 ℃, the duration from loading, transportation to unloading shall not exceed 60 minutes; if the ambient temperature is lower than + 25 ℃, the above time shall not exceed 90 minutes.
4、冬期施工時,應切實做到:開機前檢查是否結冰;下班時認真排除拌筒內及供水系統內殘存積水,關閉水泵開關,將控制手柄置于“停止”位置。
4. During winter construction, it is necessary to check whether there is icing before starting the machine; when off duty, carefully remove the residual water in the mixing drum and water supply system, turn off the water pump switch, and put the control handle at the "stop" position.
5、在施工現場卸料完畢后,應立即用該設備隨帶的軟管沖洗進料斗、出料斗、卸料溜槽等處,粘附在車身各處的污泥及混凝土。在返回攪拌站的途中,應向攪拌筒內注150---200L水以清洗筒壁及葉片粘結的混凝土殘渣。
5. After unloading at the construction site, the inlet hopper, discharge hopper and discharge chute should be flushed with the hose attached to the equipment to remove the sludge and concrete adhering to the vehicle body. On the way back to the mixing station, 150-200l water should be injected into the mixing drum to clean the concrete residue bonded by the cylinder wall and blades.
6、每天工作結束后,司機應負責向自動上料混凝土攪拌車攪拌筒內注入清水并高速(14—18轉/分)旋轉5—10分鐘,然后將水排去,以保證筒內清潔。用高壓水清洗攪拌筒各個部分時,應注意避開儀表及操縱桿等部位。壓力水噴嘴與車身油漆表面間的距離不得小于40厘米。
6. At the end of each day's work, the driver should be responsible for injecting fresh water into the mixing drum of the automatic loading concrete mixer, rotate it at high speed (14-18 RPM) for 5-10 minutes, and then drain the water to ensure the cleanness of the drum. When cleaning each part of the mixing drum with high pressure water, pay attention to avoid the instrument and control rod. The distance between the pressure water nozzle and the paint surface of the vehicle body shall not be less than 40 cm.
今天的關于如何使用
自動攪拌一體機可以提高工作效率就分享到這里,若您需要了解自動攪拌一體機其他問題歡迎及時聯系我們,或登錄我們的網站進行查詢,感謝您一直以來的關注和支持。
Today's about how to use the automatic mixer can improve work efficiency. If you need to know about other problems of the automatic mixer, please contact us in time, or log in to our official website for inquiry. Thank you for your attention and support.