隨著自動攪拌一體車的成本持續增加,輪胎價格也隨之上漲。如果使用不當,會造成異常磨損。自動攪拌一體車的輪胎多久更換一次?讓我們一起學習吧。
As the cost of automatic mixer truck continues to increase, tire prices also rise. If used improperly, it will cause abnormal wear. How often do the tires of all-in-one truck change? Let's study together.
1.輪胎胎面深度
1. Tire tread depth
胎面花紋的厚度必須大于1.6毫米。如果您駕駛的是低摩擦濕路面,請確保胎面花紋厚度是上述值的兩倍。您可以購買量規中學習,以測量胎面花紋的厚度;然而,較老的駕駛員經常使用廣泛傳播的方法粗略估計胎面花紋的厚度,即花費一美元并跟隨它。將胎面凹槽沿頂部方向插入,因為從邊緣到頂部的距離在1到2毫米之間,因此此時整個胎面花紋的厚度不足。
The thickness of the tread pattern must be greater than 1.6 mm. If you are driving on a low friction wet road, make sure that the tread thickness is twice that. You can buy gauges to learn to measure the tread thickness; however, older drivers often use a widely spread method to roughly estimate the tread thickness, that is, to spend a dollar and follow it. Insert the tread groove in the top direction because the distance from the edge to the top is between 1 and 2 mm, so the thickness of the entire tread pattern is insufficient.
2.胎面花紋磨損指示線
2. Tread wear indicator line
新輪胎的設計比過去的老式產品更加用戶友好:胎面花紋磨損指示器。當輪胎非常新或具有非常低的磨損水平時,這些指示器幾乎不可察覺,但是當磨損達到一定水平時,隱藏在胎面沖溝中的這些線出現。胎面花紋磨損指示線是扁平橡膠條,其在胎面的縱向方向上垂直地嵌入胎面凹槽中。當您檢查輪胎并偶爾找到一條或兩條指示線時,胎面花紋的厚度已經減少了很多。在這種情況下,在濕滑的道路上行駛時應小心。如果輪胎上的幾乎所有指示線都清晰可見,則需要盡快更換輪胎。
The design of the new tire is more user-friendly than the old one: tread wear indicator. These indicators are almost imperceptible when the tire is very new or has a very low wear level, but when the wear reaches a certain level, these lines hidden in the tread grooves appear. The tread pattern wear indicator line is a flat rubber strip, which is vertically embedded in the tread groove in the longitudinal direction of the tread. When you check the tire and occasionally find one or two indicator lines, the tread thickness has been reduced a lot. In this case, be careful when driving on slippery roads. If almost all the indicator lines on the tire are clearly visible, the tire needs to be replaced as soon as possible.
3.輪胎側壁裂縫
3. Tire sidewall cracks
輪胎上的問題并非都集中在胎面上,并且輪胎的側壁存在一些問題。尋找輪胎側壁上肉眼可見的裂縫和切口。這些微小的凹槽表明輪胎可能在未來泄漏,更糟糕的是,輪胎爆裂。這些輪胎故障是我們想要避免的。因此,當輪胎的側壁裂縫看起來更嚴重時,車輛被驅動到維修車間以快的速度更換輪胎。
Not all the problems on the tire are concentrated on the tread, and there are some problems on the sidewall of the tire. Look for visible cracks and cuts in the tire sidewall. These tiny grooves indicate that the tire may leak in the future and, worse, burst. These tire failures are what we want to avoid. As a result, when the sidewall cracks look more severe, the vehicle is driven to the workshop to change the tire as quickly as possible.
4.輪胎上的鼓脹和起泡
4. Bulging and blistering on tires
在一些情況下,由于強度不足,輪胎的外表面可能上升并在正常輪胎的表面上方起泡。輪胎也面臨著類似的情況。如果您未能將車輛運送到維修店并注意到輪胎故障,則胎面強度不足的區域可能會突然高速爆裂。輪胎爆裂甚可能對駕駛員和乘客造成嚴重傷害。
In some cases, the outer surface of the tire may rise and blister over the surface of the normal tire due to insufficient strength. Tires face a similar situation. If you fail to deliver the vehicle to the repair shop and notice a tire failure, areas with insufficient tread strength may burst suddenly at high speed. A burst tire may even cause serious injury to the driver and passengers.
在車輛行駛期間不可避免地會出現一定量的抖動,尤其是在惡劣的道路條件下。當您有一定的駕駛體驗時,您可以感覺到合理范圍內的抖動以及抖動如何表明車輛出現故障。
It is inevitable that there will be a certain amount of jitter during the vehicle driving, especially under the bad road conditions. When you have a certain driving experience, you can feel the shaking within a reasonable range and how the shaking indicates that the vehicle is in trouble.
自動攪拌一體車的輪胎個更換問題介紹就是這樣了,希望對你有幫助。
This is the first tire replacement problem of automatic mixing truck. I hope it can help you.