自動攪拌一體機,是一種結合了混凝土運輸車和混凝土攪拌站功能為一體,集混凝土裝料、計量、攪拌、出料于一身,并可實現混凝土運輸和現場混凝土施工作業的攪拌設備。那么自動攪拌一體機主機多久清理一次合適呢?
Automatic mixing machine is a mixing equipment which combines the functions of concrete truck and concrete mixing station, integrates concrete loading, metering, mixing and discharging, and can realize concrete transportation and on-site concrete construction. So how often is it appropriate to clean the main machine of automatic mixing machine?
自動攪拌一體機的控制技術要求
Control technical requirements of automatic mixer
1.各筒體,控制閥,電機按混凝土攪拌過程的要求運行,各筒體,控制閥,電機的控制必須準確,穩定,可靠。自上料混凝土攪拌車廠家它可裝運由攪拌廠(站)生產的混凝土或按配比混合的骨料(砂、石子)、水泥和水,在運輸過程中,不斷對濕料慢慢攪拌,防止混凝土在運輸過程中初凝和離析。
1. Each cylinder, control valve and motor shall operate according to the requirements of concrete mixing process. The control of each cylinder, control valve and motor must be accurate, stable and reliable. From the manufacturer of loading concrete mixer, it can transport the concrete produced by the mixing plant (station) or the aggregate (sand, stone), cement and water mixed according to the proportion. In the process of transportation, the wet material is continuously mixed slowly to prevent the initial setting and segregation of concrete in the process of transportation.
控制系統有自動和手動兩種工作方式,它們相互獨立,相互制約。
The control system has two working modes, automatic and manual, which are independent and restrict each other.
2.系統發展具有一個良好的抗干擾能力和完善的報警自保護管理功能;
2. The system has a good anti-interference ability and perfect alarm self-protection management function;
3.通過與計算機通訊,可以進行顯示信息系統管理工作狀態、故障報警;
3. Through the communication with the computer, it can display the management status of the information system and give an alarm;
它的主機多久清洗一次合適呢?
How often is it appropriate to clean the mainframe?
一個工作周期內攪拌車主機系統少應清洗1次。每天可以生產活動結束后,則應對攪拌車主機信息進行比較的清洗,方法是:在清洗服務過程中,將水及少許石子放進攪拌主機內通過攪拌5~10min,清洗后將機內物料管理全部有效,不得有積水、積料;停機后再沖洗以及管道,攪拌罐內外環境灰塵和粘附的混凝土。一般這種情況下,JS1000型攪拌設備主機之間加水約150~180kg左右,其他產品型號選擇主機可據此分析增減,也可自備高壓水槍或者進行數據清理。
The mixer host system should be cleaned at least once in a working cycle. At the end of daily production activities, the information of mixer host should be cleaned comprehensively. The method is as follows: in the process of cleaning service, put water and a little stone into the mixer host, and mix for 5-10 minutes. After cleaning, all materials in the mixer should be effectively removed without ponding and accumulation; After shutdown, the pipes and pipes shall be washed to remove the dust inside and outside the mixing tank and the adhered concrete. In general, about 150-180kg of water is added between the main machines of JS1000 mixing equipment. The main machines of other product models can be selected according to the analysis, and they can also have their own high-pressure water gun or carry out data cleaning.
在沖洗攪拌主機料門時,應避免上部沖洗下的積料形成異物卡滯料門現象。攪拌過程中,若混凝土運輸車較長時間沒有到位(超過20~30min,尤其在夏季),應加水對攪拌機進行簡易清洗。
When washing the material door of the main mixer, it should be avoided that the material accumulated under the upper part of the mixer will form a foreign body blocking the material door. In the process of mixing, if the concrete truck is not in place for a long time (more than 20-30min, especially in summer), water should be added to the mixer for simple cleaning.
攪拌車設備正常生產期間,要定期檢查攪拌筒內及攪拌軸上混凝土的凝固情況,如有凝結應及時按要求進行人工鏟除。人工清理攪拌筒前,必須切斷電源、氣路,放凈余氣、鎖好控制室;人工清理攪拌筒時,嚴禁猛烈敲擊攪拌軸、攪拌臂及攪拌葉片。
During the normal production of the mixer, the concrete setting in the mixing drum and on the mixing shaft should be checked regularly. If there is any setting, it should be removed manually in time according to the requirements. Before manually cleaning the mixing drum, the power supply and gas path must be cut off, the residual gas must be discharged, and the control room must be locked; When manually cleaning the mixing drum, it is strictly forbidden to strike the mixing shaft, mixing arm and mixing blade violently.
自動上料攪拌機用沖洗充電門,上部沖洗避免夾在充電門的現象形成的異物積累的材料時的攪拌主機設備?;旌线^程中,如果不再有在現澆混凝土卡車(超過20?30分鐘,尤其是夏天),水應加入攪拌機,便于清洗。
Automatic feeding mixer with flushing charging door, upper flushing to avoid the phenomenon of clamping in the charging door formed by the accumulation of foreign materials when the mixing host equipment. During mixing, if there is no longer a truck in cast-in-place concrete (more than 20? 30 minutes, especially in summer), water should be added to the mixer for easy cleaning.